Added to cart
Added to cart
Go to shopping cart
  1. Home
  2. Services
  3. Fasteners / Firestop / Strut
  4. Concrete Anchors
  5. Adhesive Anchor HIT-HY 200

ADHESIVE ANCHOR HIT-HY 200 SYSTEM

The best just got better.

Now you can set rebar, threaded rod, and internally threaded anchors in both concrete and grout filled masonry up to 60% faster without any hole cleaning with Hilti SafeSet™ technology. 

Hilti offers the highest performing, most reliable anchoring solutions in the industry. HIT-HY 200 now adds ICC-ES approval for grout filled CMU and twenty percent higher published loads on average in cracked concrete, giving you even more security in seismic anchoring applications. HIT-HY 200 with SafeSet™ Technology eliminates the need for manual hole cleaning, which increases productivity all while using a system that meets the new OSHA regulations for silica dust. Take productivity and reliability to the next level with Hilti HIT-HY 200 and SafeSet™ Technology.

HILTI HIT-HY200 SYSTEM WITH SAFE SET TECHNOLOGY

Shop Now

  • HY 200-A
    HIT-HY 200-A
    Ideal working time based on application and temperature conditions
  • HIT-HY 200-R
    HIT-HY 200-R
    Working time optimized for rebar and deep anchoring applications

Better adhesives mean stronger anchors

Don’t sacrifice confidence for convenience. With the Hilti Adhesive Anchor system, you get both.

Worried about the demands of the job? Relax. We’ve formulated two special adhesives— HIT-HY 200-R (regular working time) and HIT-HY 200-A (advanced working time)—to handle just about anything the job throws at you. HIT-HY 200 is approved for use in uncracked and cracked concrete in all seismic zones, grout filled masonry, and now you take no reductions for use in water saturated concrete (Category 1). 

How about anchor concerns? Post-installed rebar is a given. It’s one of the most popular uses for the HIT-HY 200 System. You also have several threaded-anchor choices to match your budget and the scope of your project. In fact, we’ve even engineered one of them—our Hilti HIT-Z anchors with a cone-shaped helix design—specifically for timesaving, labor-saving Safe Set™ Technology installation.

Two quicker routes to a job well done

Drill clean holes for rebar or threaded anchors, in one step.

One of the differences behind SafeSet™ Technology is the hollow drill-bit technology that removes concrete dust as you drill, eliminating a half-dozen hole-cleaning steps. That’s enough to reduce the time for installation labor by up to 60 percent as compared to traditional methods. This total solution works with Hilti SDS-Plus and SDS-Max hammer drill connections and Hilti vacuums.

HY 200 with Hollow Drill Bit and VC 20/40 Vacuum

Or skip the cleaning altogether with HIT-Z anchors.

If you want to use a threaded anchor, you can skip the hole-cleaning process altogether simply by choosing Hilti HIT-Z anchors. Go right from drilling the hole to inserting the adhesive and setting the anchor. It doesn’t get any simpler than that.

HY 200 with HIT-Z anchors

Share

Hilti = registered trademark of Hilti Corporation, 9494 Schaan, Liechtenstein
© 2009-2016, Right of technical and programme changes reserved, S.E. & O.

Hilti USA
Service Hotline: (800) 879-8000
CONTACT US
CONTACT US
Call us
Call us
You can reach us toll free at:
1-800-879-8000
Customer Service hours of operation: :
Let us call you back
Request callback
We can call you during our business hours:
*Required fields
Live chat with us
Chat
Send us a message
Send us a message
Use the following form to send us your request.
* Required fields
You will receive an e-mail copy of your message.
* Required fields
Looking for a Hilti store? Find a Hilti center